 |
9323 Hamilton
Mentor, Ohio 44060 - USA
Tel:+1-440-357-1400
Fax:+1-440-357-1416
|
Scientific Solutions ® Inc.,
LabMaster ® DPCI for Photon Technologies
International (PTI) Felix
DeskTop PTI Front View - shows BNC
connections
DeskTop PTI Back View - shows
connections for the computer and the power supply
Description
of the LabMaster DPCI for PTI Felix Product
The LabMaster DPCI product consists of two main items;
(1). The LabMaster DPCI computer interface which is installed a PCI
slot of the computer
(2). DeskTop unit that contains the BNC connections and circuitry away
from
any internal computer noise.
In this configuration, the DeskTop unit contains BNC connections
that are configured particularly for the PTI Felix software. This
allows current ISA customers to easily migrate to a PCI based solution
by unplugging the signal connections from their older PTI DeskTop unit
and connect them to the new Scientific Solutions PTI DeskTop unit..
The DeskTop unit has the following BNC Connections on the front:
O
TRIGGER
|
O
SIGNAL
|
O
C1
|
O
A1
|
O
A3
|
O
A5
|
IN
O
|
O
OUT-1
|
CONTROL
O
|
GAIN
O
|
C2
O
|
A2
O
|
A4
O
|
A6
O
|
OUT-2
O
|
CHOPPER
|
X-COR
|
COUNTER
|
ANALOG
IN
|
TTL
IN
|
TTL
OUT
|
- Chopper
- Trigger (input)
- Control (output)
- X-COR (also called RCQC)
- Signal (input)
- Gain (output)
- Counter (also called PMT)
- C1 (also called A Chan) (input)
- C2 (also called B Chan) (input)
- Analog In (also called Shutter)
- A1 (also called S1) (input)
- A2 (also called S2) (input)
- A3 (input)
- A4 (input)
- A5 (input)
- A6 (input)
- TTL In (also called Ext. Trig.)
- TTL Out (also called Detectors)
- Out-1 (also called a) (output)
- Out-2 (also called d) (output)
On the back of the DeskTop unit is a DB25 connection that provides
Digital I/O connections.
Also on the back of the DeskTop unit are connections for the LabMaster
DPCI computer interface and for the power supply. The LabMaster
connection is a
DB25 pin connector. The power supply uses a 2.1mm positive center
post connection. The LabMaster DPCI requires a 5v power supply
that is also provided with the unit.
All of the data acquisition cirucits A/D, D/A, Digital I/O ,
Counter/Timer are external to the computer and are controlled by the
LabMaster DPCI card in the computer using a single quick-connect round
cable. The LabMaster DPCI is 100% register level compatible to
the original PC LabMaster product introduced in 1981.
LabMaster
DPCI DeskTop Unit:
The DeskTop unit is about 11" wide x 7" deep x 4" high (280mm x 180mm x
100 mm).
A light on the front of the DeskTop Unit illuminates to indicate the
presence of power.
Close-Up Front View of DeskTop unit
The
LabMaster DPCI Card:
The LabMaster DPCI card is a small card that installs into a 32-bit PCI
slot. It is approximately 2" x 4" (50mm x 100mm). The card
has a single DB25 socket connector.
LabMaster DPCI PC Interface shown.
Connecting the LabMaster DPCI and the
DeskTop Unit:
To connect the LabMaster DPCI and the DeskTop Unit, use the
following steps:
- Install the LabMaster DPCI card into your computer
- Attach the power supply (included) to the DeskTop unit.
- Connect the cable (also included) between the LabMaster DPCI card
installed in the computer and the DeskTop unit.
- Turn the power ON to your computer.
- Now note that the light on the front of the DeskTop unit will
illuminate when the power supply is attached and the computer is
powered on. The DeskTop unit requires both the power
supply to
be connected AND the computer to be on in order to provide power to its
internal circuits. The DeskTop unit automatically powers on when
the
computer is on and automatically turns off when the computer is off.
|
|
DeskTop
Unit Power Supply
(Included with product) |
LabMaster
DPCI to DeskTop Cable
(Included with Product)
|
Specifications subject to change without notice.
Scientific Solutions liability, trademarks, and export notices apply.
Copyright © 1974-2014 Scientific Solutions - All rights reserved
